PARTING REAPER.... possibly - Page 3 - General Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
Re: PARTING REAPER.... possibly
Wednesday, February 10, 2016 6:49 AM
DFF- Breaking The Boundary wrote:
DFF- Breaking The Boundary wrote:Engine-
Stock 96 block- bored .060-$2500-- Motor includes all parts from shortblock----------PRICE CUT
All Clevite 77 bearings
Hot tanked block
Crower I beam rods
Cp custom flat top pistons 10.1 compression
Swain tech coated pistons
Deleted balance shafts
Deleted factory oil pump system
7qt Dry sump oil system
Barnes 3 stage pump-$1150 ( this is the complete system, pump, tank, gear lines etc)-------PRICE CUT
Lightweight Factory balanceD pulley- MD ENFORCER---$100
Rotating assembly fully balanced
Ported and polished head
1mm Oversized valves
Titanium Retainers
2.3 QUAD 4 HO cam shafts
2.3 QUAD 4 HO cam shaft housings
Cometic MLS head gasket .035 thick
ARP Rod bolts, main bolts and head bolts
Custom made Oil pan with heatsink
Custom made Tubular Header-$450 ( called by BLWn LD9)--------------------------------------SOLD
Custom made LOG intake manifold with velocity stacks-$450------PRICE CUT
TTR upper motor mounts-$75
Poly lower Mounts and Transmission mount-$50
80MM throttle Body-$150----------SOLD
Phenolic head Spacer-$20
T3/T4 turbonetics turbo-$250----PRICE CUT--------SOLD
3" Dump all the way to back-$250
Aluminum exhaust from firewall back-$100
Electric WaterPump-$300---SOLD
Becool 3" core aluminum radiator-$250
160* Thermostat
Fuel LAB AFPR-$80
Tial Waste gate-$125---HOLD FOR JASON-------SOLD
Tial BOV-$125---------SOLD
Intercooler HAHN http://www.turbosystem.com/hahn/parts/intercool.htm- $300------HOLD FOR TREY-------SOLD

Suspension

Custom made KONI Race Coilovers with 700# in front and 800# in back Hyperco Springs-$1000----SOLD
Custom made Tubular control arms-$350----SOLD
Modified rear torsion beam WITH POLY BUSHINGS ------$200
BBS 2 piece wheels with BFG KDW Tires 235/45/17----$700-------SOLD
Front Addco sway bar with poly bushings-$80----SOLD
Wilwood 4 Piston brakes front-$1000---SOLD
Disc conversion for Rear brakes--$250---PRICE CUT-------SOLD
N Body Knuckle upgrade in front- $350---SOLD
Camber plates front---SOLD----SHIPPED
Spherical rear Mounts in rear---SOLD---SHIPPED
Custom made Subframe brace-$75----SOLD---SHIPPED
Custom made K brace-$200----SOLD----SHIPPED
Custom made rear Triangulated rear brace----SOLD----SHIPPED
Bump Steer Kit Custom made-$50----SOLD
Custom made Overflow tank-$40----SOLD

Transmission
35k mile 01 Getrag transmission fully torn apart and checked over-$2000 (Comes with Quaife LSD)-----PRICE CUT
Spec stage 4 clutch-$200
Rk sport Aluminum Flywheel-$200
ARP Flywheel bolts--$10
Custom fit LD9 jack shaft. TO F23 TRANS---$300

Fuel

10 gallon fuel cell-----
2 Walbro 255HP Out of tank fuel pumps
Fully walked AN fittings and hose front to back
42# Green tops injectors
Custom built fuel rail-$400 with lines
Aeromotive Adjustable FPR


Other

Custom built roll cage 8pt-----$750
AEM Boost controller- $180-----SOLD
Autometer ULTRA LITE DIGITAL 6545 EGT- $125
AutoMeter ULTRA LITE PRO COMP boost gauge 4301-$40-------SOLD
Autometer ULTRA LITE DIGITAL 6537Water temp-$80-----------SOLD
Innovate Wideband-$150
AutoMeter ULTRA LITE PRO COMP 4347 Oil Temp-$40
AutoMeter Oil PSI- $30-----SOLD----SHIPPED
Sparco seats- $750-------SOLD---SHIPPED
Scrotch 3" harnesses-$250----SOLD
Emergency Battery cut off switch
Front and rear Tow Hooks---------SOLD $15
TOYO TAILS- $150----Hold for Ecoswapped-----SOLD--- SHIPPED
projector headlights--$50
Hp tuners computer-$50------SOLD
Engine harness with computer- $150-------SOLD
Intercooler piping- $150
Couplers-$30
Hood and Trunk-----HOLD FOR JOHN HIGGENS---$300
Import Fighter Kit----$500---HOLD FOR AUSTIN----SOLD



http://www.overkillengineeringmotorsports.com/

Re: PARTING REAPER.... possibly
Monday, February 15, 2016 6:35 AM
Engine-
Stock 96 block- bored .060-$3000-- Motor includes all parts from shortblock----------PRICE CUT
All Clevite 77 bearings
Hot tanked block
Crower I beam rods
Cp custom flat top pistons 10.1 compression
Swain tech coated pistons
Deleted balance shafts
Deleted factory oil pump system
7qt Dry sump oil system
Barnes 3 stage pump this is the complete system, pump, tank, gear lines etc)-------PRICE CUT
Lightweight Factory balanced pulley- MD ENFORCER---$100
Rotating assembly fully balanced
Ported and polished head
1mm Oversized valves
Titanium Retainers
2.3 QUAD 4 HO cam shafts
2.3 QUAD 4 HO cam shaft housings
Cometic MLS head gasket .035 thick
ARP Rod bolts, main bolts and head bolts
Custom made Oil pan with heatsink

Custom made LOG intake manifold with velocity stacks-$450------PRICE CUT
TTR upper motor mounts-$75
Poly lower Mounts and Transmission mount-$50

Phenolic head Spacer-$20

3" Dump all the way to back-$250
Aluminum exhaust from firewall back-$100

Becool 3" core aluminum radiator-$250
160* Thermostat
Fuel LAB AFPR-$80


Suspension


Modified rear torsion beam WITH POLY BUSHINGS ------$200


Transmission
35k mile 01 Getrag transmission fully torn apart and checked over-$2000 (Comes with Quaife LSD)-----PRICE CUT
Spec stage 4 clutch-$200
Rk sport Aluminum Flywheel-$200
ARP Flywheel bolts--$10
Custom fit LD9 jack shaft. TO F23 TRANS---$300

Fuel

10 gallon fuel cell-----
2 Walbro 255HP Out of tank fuel pumps
Fully walked AN fittings and hose front to back
42# Green tops injectors
Custom built fuel rail-$400 with lines
Aeromotive Adjustable FPR


Other

Custom built roll cage 8pt-----$750

Autometer ULTRA LITE DIGITAL 6545 EGT- $125

Innovate Wideband-$150


Emergency Battery cut off switch


projector headlights--$50

Intercooler piping- $150
Couplers-$30
Hood and Trunk-----HOLD FOR JOHN HIGGENS---$300



http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Tuesday, February 23, 2016 11:38 AM
Engine-
Stock 96 block- bored .060-$2300-- Motor includes all parts from shortblock And Oil pump System----------PRICE CUT
All Clevite 77 bearings
Hot tanked block
Crower I beam rods
Cp custom flat top pistons 10.1 compression
Swain tech coated pistons
Deleted balance shafts
Deleted factory oil pump system
7qt Dry sump oil system
Barnes 3 stage pump this is the complete system, pump, tank, gear lines etc)
Lightweight Factory balanced pulley- MD ENFORCER---$100
Rotating assembly fully balanced
Ported and polished head
1mm Oversized valves
Titanium Retainers
2.3 QUAD 4 HO cam shafts
2.3 QUAD 4 HO cam shaft housings
Cometic MLS head gasket .035 thick
ARP Rod bolts, main bolts and head bolts
Custom made Oil pan with heatsink

Custom made LOG intake manifold with velocity stacks-$350------PRICE CUT
TTR upper motor mounts-$75
Poly lower Mounts and Transmission mount-$50

Phenolic head Spacer-$20

3" Dump all the way to back-$250
Aluminum exhaust from firewall back-$100

Becool 3" core aluminum radiator-$250
160* Thermostat
LD9 Fuel rail with Fuel LAB AFPR-$150


Suspension


Modified rear torsion beam WITH POLY BUSHINGS ------$200


Transmission
35k mile 01 Getrag transmission fully torn apart and checked over-$1500 (Comes with Quaife LSD)-----PRICE CUT
Spec stage 4 clutch-$200
Rk sport Aluminum Flywheel-$200
ARP Flywheel bolts--$10
Custom fit LD9 jack shaft. TO F23 TRANS---$300

Fuel

10 gallon fuel cell-----
2 Walbro 255HP Out of tank fuel pumps
Fully walked AN fittings and hose front to back
42# Green tops injectors
Custom built fuel rail-$400 with lines
Aeromotive Adjustable FPR


Other

Custom built roll cage 8pt-----$750

Autometer ULTRA LITE DIGITAL 6545 EGT- $125

Innovate Wideband-$150


Emergency Battery cut off switch


projector headlights--$50

Intercooler piping- $150
Couplers-$30
Hood and Trunk-----HOLD FOR JOHN HIGGENS---$300


http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Tuesday, February 23, 2016 12:03 PM
Wish I could have been the one to snag the wheels



I miss my Cavalier, even if it made 100 hp on a cold day and had more suspension then it deserved.
Re: PARTING REAPER.... possibly
Thursday, February 25, 2016 7:44 AM
Motor and trans need to go ASAP


http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Thursday, February 25, 2016 11:21 AM
DFF- Breaking The Boundary wrote:Engine-
Stock 96 block- bored .060-$2300-- Motor includes all parts from shortblock And Oil pump System----------PRICE CUT
All Clevite 77 bearings
Hot tanked block
Crower I beam rods
Cp custom flat top pistons 10.1 compression
Swain tech coated pistons
Deleted balance shafts
Deleted factory oil pump system
7qt Dry sump oil system
Barnes 3 stage pump this is the complete system, pump, tank, gear lines etc)
Lightweight Factory balanced pulley- MD ENFORCER---$100
Rotating assembly fully balanced
Ported and polished head
1mm Oversized valves
Titanium Retainers
2.3 QUAD 4 HO cam shafts
2.3 QUAD 4 HO cam shaft housings
Cometic MLS head gasket .035 thick
ARP Rod bolts, main bolts and head bolts
Custom made Oil pan with heatsink

Custom made LOG intake manifold with velocity stacks-$350------PRICE CUT
TTR upper motor mounts-$75
Poly lower Mounts and Transmission mount-$50

Phenolic head Spacer-$20

3" Dump all the way to back-$250
Aluminum exhaust from firewall back-$100

Becool 3" core aluminum radiator-$250
160* Thermostat
LD9 Fuel rail with Fuel LAB AFPR-$150


Suspension


Modified rear torsion beam WITH POLY BUSHINGS ------$200


Transmission
35k mile 01 Getrag transmission fully torn apart and checked over-$1500 (Comes with Quaife LSD)-----PRICE CUT
Spec stage 4 clutch-$200
Rk sport Aluminum Flywheel-$200
ARP Flywheel bolts--$10
Custom fit LD9 jack shaft. TO F23 TRANS---$300----HOLD FOR JASON

Fuel

10 gallon fuel cell-----
2 Walbro 255HP Out of tank fuel pumps
Fully walked AN fittings and hose front to back
42# Green tops injectors
Custom built fuel rail-$400 with lines
Aeromotive Adjustable FPR


Other

Custom built roll cage 8pt-----$750

Autometer ULTRA LITE DIGITAL 6545 EGT- $125

Innovate Wideband-$150


Emergency Battery cut off switch


projector headlights--$50

Intercooler piping- $150
Couplers-$30
Hood and Trunk-----HOLD FOR JOHN HIGGENS---$300



http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Saturday, February 27, 2016 7:55 AM
Engine-
Stock 96 block- bored .060-$2300-- Motor includes all parts from shortblock And Oil pump System----------PRICE CUT
All Clevite 77 bearings
Hot tanked block
Crower I beam rods
Cp custom flat top pistons 10.1 compression
Swain tech coated pistons
Deleted balance shafts
Deleted factory oil pump system
7qt Dry sump oil system
Barnes 3 stage pump this is the complete system, pump, tank, gear lines etc)
Lightweight Factory balanced pulley- MD ENFORCER---$100
Rotating assembly fully balanced
Ported and polished head
1mm Oversized valves
Titanium Retainers
2.3 QUAD 4 HO cam shafts
2.3 QUAD 4 HO cam shaft housings
Cometic MLS head gasket .035 thick
ARP Rod bolts, main bolts and head bolts
Custom made Oil pan with heatsink

Custom made LOG intake manifold with velocity stacks-$350------PRICE CUT
TTR upper motor mounts-$75
Poly lower Mounts and Transmission mount-$50

Phenolic head Spacer-$20

3" Dump all the way to back-$250
Aluminum exhaust from firewall back-$100

Becool 3" core aluminum radiator-$250
160* Thermostat
LD9 Fuel rail with Fuel LAB AFPR-$150


Suspension


Modified rear torsion beam WITH POLY BUSHINGS ------$200


Transmission
35k mile 01 Getrag transmission fully torn apart and checked over-$1500 (Comes with Quaife LSD)-----PRICE CUT
Spec stage 4 clutch-$200
Rk sport Aluminum Flywheel-$200
ARP Flywheel bolts--$10
Custom fit LD9 jack shaft. TO F23 TRANS---$300----HOLD FOR JASON

Fuel

10 gallon fuel cell-----
2 Walbro 255HP Out of tank fuel pumps
Fully walked AN fittings and hose front to back
42# Green tops injectors
Custom built fuel rail-$400 with lines
Aeromotive Adjustable FPR


Other

Custom built roll cage 8pt-----$750

Autometer ULTRA LITE DIGITAL 6545 EGT- $125

Innovate Wideband-$150


Emergency Battery cut off switch


projector headlights--$50

Intercooler piping- $150
Couplers-$30
Hood and Trunk-----HOLD FOR JOHN HIGGENS---$300-------SOLD


http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Monday, February 29, 2016 6:14 AM
DFF- Breaking The Boundary wrote:Engine-
Stock 96 block- bored .060-$2300-- Motor includes all parts from shortblock And Oil pump System----------PRICE CUT
All Clevite 77 bearings
Hot tanked block
Crower I beam rods
Cp custom flat top pistons 10.1 compression
Swain tech coated pistons
Deleted balance shafts
Deleted factory oil pump system
7qt Dry sump oil system
Barnes 3 stage pump this is the complete system, pump, tank, gear lines etc)
Lightweight Factory balanced pulley- MD ENFORCER---$100
Rotating assembly fully balanced
Ported and polished head
1mm Oversized valves
Titanium Retainers
2.3 QUAD 4 HO cam shafts
2.3 QUAD 4 HO cam shaft housings
Cometic MLS head gasket .035 thick
ARP Rod bolts, main bolts and head bolts
Custom made Oil pan with heatsink


TTR upper motor mounts-$75
Poly lower Mounts and Transmission mount-$50

Phenolic head Spacer-$20

3" Dump all the way to back-$250
Aluminum exhaust from firewall back-$100

Becool 3" core aluminum radiator-$250
160* Thermostat
LD9 Fuel rail with Fuel LAB AFPR-$150


Suspension


Modified rear torsion beam WITH POLY BUSHINGS ------$200


Transmission
35k mile 01 Getrag transmission fully torn apart and checked over-$1500 (Comes with Quaife LSD)-----PRICE CUT
Spec stage 4 clutch-$200
Rk sport Aluminum Flywheel-$200
ARP Flywheel bolts--$10
Custom fit LD9 jack shaft. TO F23 TRANS---$300----HOLD FOR JASON

Fuel

10 gallon fuel cell-----
2 Walbro 255HP Out of tank fuel pumps
Fully walked AN fittings and hose front to back
42# Green tops injectors
Custom built fuel rail-$400 with lines
Aeromotive Adjustable FPR


Other

Custom built roll cage 8pt-----$750

Autometer ULTRA LITE DIGITAL 6545 EGT- $125

Innovate Wideband-$150


Emergency Battery cut off switch


projector headlights--$50





http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Wednesday, March 09, 2016 6:54 AM



TTR upper motor mounts-$75
Poly lower Mounts and Transmission mounst-$75

Phenolic head Spacer-$20



LD9 Fuel rail with Fuel LAB AFPR-$150


Suspension


Modified rear torsion beam WITH POLY BUSHINGS ------$200


Transmission
35k mile 01 Getrag transmission fully torn apart and checked over-$1500 (Comes with Quaife LSD)-----PRICE CUT
Spec stage 4 clutch-$150
Rk sport Aluminum Flywheel-$150
ARP Flywheel bolts--$10
Custom fit LD9 jack shaft. TO F23 TRANS---$300----HOLD FOR JASON

Fuel

10 gallon fuel cell-----
2 Walbro 255HP Out of tank fuel pumps
Fully walked AN fittings and hose front to back
42# Green tops injectors
Custom built fuel rail-$400 with lines
Aeromotive Adjustable FPR


Other

Custom built roll cage 8pt-----$750

Autometer ULTRA LITE DIGITAL 6545 EGT- $125

Innovate Wideband-$150


Emergency Battery cut off switch


projector headlights--$50


http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Wednesday, March 09, 2016 6:57 AM
Re: PARTING REAPER.... possibly
Wednesday, March 16, 2016 7:00 AM
DFF- Breaking The Boundary wrote:TTR upper motor mounts-$75
Poly lower Mounts and Transmission mounst-$75






Suspension


Modified rear torsion beam WITH POLY BUSHINGS ------$200


Transmission
35k mile 01 Getrag transmission fully torn apart and checked over-$1500 (Comes with Quaife LSD)-----PRICE CUT
Spec stage 4 clutch-$150
Rk sport Aluminum Flywheel-$150
ARP Flywheel bolts--$10
Custom fit LD9 jack shaft. TO F23 TRANS---$300----HOLD FOR JASON


Other

Custom built roll cage 8pt-----$750

Autometer ULTRA LITE DIGITAL 6545 EGT- $125

Innovate Wideband-$150


Emergency Battery cut off switch


projector headlights--$50



http://www.overkillengineeringmotorsports.com/

Re: PARTING REAPER.... possibly
Sunday, March 20, 2016 8:59 AM
Re: PARTING REAPER.... possibly
Sunday, March 20, 2016 11:03 PM
Pm'd about the radiator. Is it still available?
Re: PARTING REAPER.... possibly
Tuesday, March 22, 2016 7:27 AM
Re: PARTING REAPER.... possibly
Friday, March 25, 2016 8:57 AM
Last bit of parts

Shifter with cables- $50
TTR Upper Mount- $50
Lower Poly mount- $20
Trans mounts for F23- $75 for both
Clutch- $150
Flywheel- $150
One Off airbag gauge holder- $50
F23 trans with Quaife Diff for 2.4 LD9- $1250
Shifter boot- $25
MSD Neon coil conversion- $75
Camber plates- $125










http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Tuesday, April 26, 2016 12:04 PM
MAKE AN OFFER ON ANY AND ALL PARTS. NEED GONE ASAP


http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Monday, May 02, 2016 10:52 AM
Re: PARTING REAPER.... possibly
Friday, May 13, 2016 11:50 AM
DFF- Breaking The Boundary wrote:Last bit of parts

Shifter with cables- $50-----SOLD
TTR Upper Mount- $50
Lower Poly mount- $20
Trans mounts for F23- $75 for both----SOLD
Clutch- $150
Flywheel- $150
One Off airbag gauge holder- $50
F23 trans with Quaife Diff for 2.4 LD9- $1250--Pending
Shifter boot- $25
MSD Neon coil conversion- $75
Camber plates- $125










http://www.overkillengineeringmotorsports.com/
Re: PARTING REAPER.... possibly
Friday, June 03, 2016 9:54 AM
DFF- Breaking The Boundary wrote:
DFF- Breaking The Boundary wrote:Last bit of parts

Shifter with cables- $50-----SOLD
TTR Upper Mount- $50
Lower Poly mount- $20
Trans mounts for F23- $75 for both----SOLD
Clutch- $150
Flywheel- $150
One Off airbag gauge holder- $50---SOLD
F23 trans with Quaife Diff for 2.4 LD9- $1250--SOLD
Shifter boot- $25
MSD Neon coil conversion- $75
Camber plates- $125



http://www.overkillengineeringmotorsports.com/
Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search