Xxr 002's with 0mm offset?? - Wheel and Tire Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
Xxr 002's with 0mm offset??
Monday, April 02, 2012 3:11 AM
Wondering if I could make these fit?? Looking for more of a dished rim, this has a nice 3.5". I know I've read around on here that anywhere around 40mm offset is ideal. Was wondering though if i could get these to fit with 0mm offset. What would I need if possible?? Would be getting 16x8's 0mm offset. And no not on stock ride height. Koni yellows with ground control coilovers. I searched but found no answers! Thank you all for you time and answers! If not possible, could you steer me in a direction with a nice rim that has a nice dished look?! Thanks again!!!

Re: Xxr 002's with 0mm offset??
Monday, April 02, 2012 7:00 PM
To run those you'd need some extreme fender work...

DO IT!




________________________________________.
Still not low enough for a signature.

Re: Xxr 002's with 0mm offset??
Monday, April 02, 2012 7:10 PM
Yea that's what I was kind of figuring. My uncles a all around mechanic, and good at body work, so I'm going to have him help me out! I'll get pics up when its all done!!
Re: Xxr 002's with 0mm offset??
Tuesday, April 03, 2012 9:36 PM
You better...




________________________________________.
Still not low enough for a signature.

Re: Xxr 002's with 0mm offset??
Sunday, April 08, 2012 6:29 PM
I'm running vette wheels 16x8.5 with an effective offset of +12 in the front and 0 in the back.

You can see pics in the photo/media section.
Re: Xxr 002's with 0mm offset??
Tuesday, April 10, 2012 12:33 AM
I've been meaning to ask you that. I've seen your build on here, and S/W. Gatta say, I'm lovin' it!




________________________________________.
Still not low enough for a signature.

Re: Xxr 002's with 0mm offset??
Monday, April 23, 2012 2:35 PM
not to tread jack but what about 18X8, +32 offset?? would that require fender work ??



Skr8 Goodz in tha hood
Re: Xxr 002's with 0mm offset??
Monday, April 23, 2012 4:27 PM
Just roll and pull.


Error: Sig not found.

Re: Xxr 002's with 0mm offset??
Tuesday, April 24, 2012 12:28 AM
Just cut and cut. Who gives a @!#$ anyway.



Re: Xxr 002's with 0mm offset??
Tuesday, April 24, 2012 9:39 AM
02_redbadged wrote:Just cut and cut. Who gives a @!#$ anyway.


Lol I like ur attitude!! n thanks for the info



Skr8 Goodz in tha hood
Re: Xxr 002's with 0mm offset??
Thursday, April 26, 2012 11:14 PM
Cavalier Thompson wrote:not to tread jack but what about 18X8, +32 offset?? would that require fender work ??



im sure you would be ok...from the looks of your profile your ADRs look to be 18x8 with a close to 38offset.. hell i ran 18x8 with a 35mm and 38mm with 10mm spacers in front and the 3/4" inch saturn adapter in rear. and i was on coils and pretty low. im sure your car would be fine.




Re: Xxr 002's with 0mm offset??
Saturday, May 12, 2012 6:16 PM
yeah they are but I'm goin with 18x8.5 +40 offset and 3/8 wheelbearing spacers in the back from Jeffie , I have those on now with the ADR's and they rub a bit I'll probably take those off and get the rear Saturn caliper setup ( just waiting on funds) and I read that they were 5/8 so I may not in the front but I should roll them in the back?



Skr8 Goodz in tha hood
Re: Xxr 002's with 0mm offset??
Monday, May 14, 2012 8:30 AM
You should roll both the front and back.




________________________________________.
Still not low enough for a signature.

Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search