Reflashed Supercharged Program with gm 2 bar for Automatic / Can also put whatever tune you want on there with my HP Tuners Pro //$225.00
cartech billet #2025 adjustable rising rate fmu. $125
3" silicone coupling $8
3" to 2.5" silicone coupling reducer //$ 8
2 @ 2" to 2.5 " silicone coupling reducer//$ 8
5 @ hose technique blue 2" silcone couplings //$ 8 each
2" polished aluminum charge piping. and bends.//$ 50
10 @ hose technique 2" t bolt clamps SS //$6 each
7@ hose technique 2.5" t bolt clamps SS //$6 each
3 @ hose technique3" t bold clamps SS// $6each
3" Polished 90 degree bend with HKS SSQV flange welded on. //$50
1 garrett dual port internal wastegate actuator 7psi //$30
1 hahn 16g single port actuator 10psi //$50
1 internal wastegate swing valve assembly //$20
Auto trans Interceptor /// $50.00
2.5 to 3" side exit oval catback exhaust// $75
Brand New RK Coils with H&R Springs // 300
JRC 8" Intercooler $ 50 /// Pick up Only
Stainless Braided feed and return line kit with AN Fittings and Bung /// $125.00
Mild steel custom externally gated and stress cut manifold/// $75
Turbonetics Polished T3- TO4E. Needs Rebuild /// $200.00
HKS Super Sequential Blow Off Valve with extra ATP Flange. ///$ 150.00
Innovate Motorsports XD1 Guage /// $100.00
2.5" mandrel bent downpipe /// $50.00
2.5" mandrel bent charge piping complete setup /// $ 125.00
Greddy Profec B Spec 2 Boost Controller /// $ 250.00









Windy City TurboZ

so is the HPT included with the gm flashed VCM?

if so you can pencil me in for it immediately...

z yaaaa wrote:so is the HPT included with the gm flashed VCM?

if so you can pencil me in for it immediately...

You do realize that the hpt pro alone is $750.. This is for a reflashed ecu with two bar map tuned however you prefer... Nice try though man lol ...


Windy City TurboZ

if this was a store i could win the argument!! lmao

i KNEW it was too good be to true, never hurts to ask though does it?

Daily bump


Windy City TurboZ

what happened to the turbo? why does it need rebuilt...?

I blew an oil seal on it from excessive oil pressure. It was used when I bought it from ken2.2.. Its a fine piece though.


Windy City TurboZ

Luke...call me man. I might steal a few things from you.



I used to race cars, now I race myself.
5K PB: 24:50
10K PB: 54:26

pm sent

Mike, I have the feed and return lines that fit this manifold right to the pan. All Stainless Steel Earls braided line and fittings. I also have a weld in aluminum bung for the pan if you need it. I cannot guarantee that these charge pipes will fit your intercooler . They will get you close but unless you use the exact same size intercooler , there might need to be some slight modifying to the piping setup but as you can see from the pictures I have literally everything you need. My setup used a divorced wastegate setup . The 38mm tial gate will not bolt right to the manifold. I have a block off flange for it as you can see in the pictures.The manifold has some slight surface rust on it right now from sitting but the flanges are perfect and not warped at all man. I have a internal wastegate swingvalve assembly and two wastegate actuators if you wanted to go internal gate. I have tons of tbolt clamps and silicone fittings.Oh before I forget, the downpipe piece that I have, I will also send you the piece that has two o2 bungs welded into it if you want. That way you can run your stock sensor and a wideband sensor, or if you want to just plug them you can. I was using a heated 4 wire gtp sensor for my stock sensor and a bosch wideband sensor . Just lemme know what you need man. Lets just say for the fmu ,downpipe with extension piece with bungs , and the manifold 275 shipped. I will totally hook you up in the future with whatever you need at a good price. I am getting out of the jbody scene and moving into a Z06 . I have done a bunch of turbo J's and have whatever you need . I will help you out along the way too. just lemme know if 270 is good with you Mike and I will ship them out asap. I will need your full address buddy.











Windy City TurboZ

Do you still have the turbo in need of rebuild?......urbonetics Polished T3- TO4E. Needs Rebuild /// $200.00

also what trim is it?

JUCNBST I sent you a PM. All messages returned. Deal pending on manifold, piping , fmu , oil lines , silicone and tbolts..... Boost controller sold . Wastegate and dumptube sold...


Windy City TurboZ

thanks for the info and the response .

manifold,downpipe,oil lines,fmu,charge piping, and couplers/t-bolts sold

is the wideband $100, or is that the gauge. I didnt see it listed and couldnt make it out in the picture.