I was wondering if anyone can tell me the original specs for a 2200 in 1999 I want to know

Rocker Ratio:
Compression Ratio:
Valve Diameter:
Cam Specs:
bore:
Stroke:

'99 2.2 OHV w/3spd auto (work in progress)

http://www.cardomain.com/ride/2322134

ny-jbodies.org library
however, rocker ratio has been measured to be 1.54, not 1.6



fortune cookie say:
better a delay than a disaster.

Anywhere to find this information now?? The website is no longer availible. This is proof i searched

----------------------------------------------------------------
www.bradsairsoft.com

I'm curious as to all these specs, too. And the one's for the '94-'97 LN2 while we're at it.

Go beyond the "bolt-on".

I have the 98+ LN2 file from the website saved on my computer(saved it cuz I figured it would be gone sooner or later), shoot me an e-mail and I'll send it to u. d356bud@yahoo.com


<img src="http://ad.nicoclub.com/banners/nico-banner1.gif" ></a>

There was a thread on here somewhere posted by tabs not long ago that had everything you would want to know.

Found this, not completely what you were looking for, but has a lot of good information about the engine in its different stages.
Here

i have a PDF file that covers the entire 2200. Send me an email and I will forward it to you. xxjazerxx@yahoo.com.

New location...thanks Kardain




fortune cookie say: better a delay than a disaster

Thanks Notec! Now I just need the same layout of specs (specifically the factory cam) for the pre-'98 LN2.

Go beyond the "bolt-on".

Thanks notec very useful I have been looking for some of that info. Now I just need to find the same thing for a 2.4.

Michael, the spec for the stock 2.2L OHV is:

Duration @ 0.050" (Int / Exh) : 198* / 198*
Lift @ the Valve (w/ 1.5 rockers) : 0.432" (@ the Lobe : 0.288")
Intake Center Line : 109* ATDC
Lobe Separation Angle : 114*

ZOMBIE THREAD!!!!!!! BRRRAAAAAIIIIINNNNNNNNS!!!!!

Anyways, I need specs too and both links in this thread are dead and Google isnt getting me anywhere. Does anyone have them?

Nobody?

do you wnat them? I can probably hunt them down here over the weekend....umm if you have a chilton's an older one they have the full spec out of it

Rocker Ratio: 1.6 (or 1.54)
Compression Ratio: 9.0 : 1
Valve Diameter: ???
Cam Specs:
Duration @ 0.050": 185*/185*
Intake Centerline: 108* ATDC
Lobe Separation Angle: 112*
Lobe Lift: 0.263"/0.263"
Lift @ Valve: 0.421"/0.421" (with cast steel needle bearing fulcrum, self-aligning rocker arms with a nominal 1.6:1 ratio. Some have been checked to an actual 1.54:1 ratio)
bore: 88mm
Stroke: 89mm

I took the cam specs off a thread from s10 forum that Mad Jack posted


______
Inochi

Thanks man. That helps with my cam questions. I still need stuff like port size. Maybe a flow bench of a stock head. Im curious about cfm and valve sizes and crap like that.

I couldn't find the valve sizes but I did find something on the valve ratio. I could go pull that back up again but I didn't find anything on the flow for the head.


______
Inochi

Balls. So how are all of you sizing turbos without flow info on the head and crap like that?

Luckily, the original article is still around-

2.2 Growing pains

.

Awesome. Thanks!

Im gonna be reading all night.

if the head is stock turbo sizing is configured using this type of info http://www.dsmtuners.com/forums/articles-turbo-system-intercooler/212923-how-choose-right-turbo.html