Rear mount setup - Boost Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
Rear mount setup
Thursday, May 27, 2010 10:54 AM
Just wondering if anyone else has done a rear mount set up on their car yet, Just finished mine today and love it.

Re: Rear mount setup
Thursday, May 27, 2010 10:59 AM
pics?

yes it has been done.



Re: Rear mount setup
Thursday, May 27, 2010 11:18 AM











Remember... One test is worth a thousand expert opinions.
Re: Rear mount setup
Thursday, May 27, 2010 11:44 AM
Mike wrote:pics?

yes it has been done.
Yup, its been done.... I did my wife's car.... The pics you posted are pretty small, can you post larger ones?

Here is the link to my wife's build....
http://www.j-body.org/forums/read.php?f=40&i=173445&t=152782&p=1





P&P Tuning
420.5whp / 359.8wtq

Re: Rear mount setup
Thursday, May 27, 2010 12:03 PM
nice man. eco too



Re: Rear mount setup
Thursday, May 27, 2010 12:06 PM
I took the pics with my phone, if they get any bigger im sure they will be pretty much un-identifable. It looks like you went way over kill it looks nice. Why did you decide to install a intercooler? Im only doing 5 pounds so my intake temps are down around a haundred degrees is why i wonder.


Remember... One test is worth a thousand expert opinions.
Re: Rear mount setup
Thursday, May 27, 2010 12:57 PM
Josh A wrote:I took the pics with my phone, if they get any bigger im sure they will be pretty much un-identifable. It looks like you went way over kill it looks nice. Why did you decide to install a intercooler? Im only doing 5 pounds so my intake temps are down around a haundred degrees is why i wonder.
We opted to used the FMIC due to the routing of the piping. The core itself is not that big, so the psi drop was minimul. We have been pushing 12-15 psi out of a T3/T4 57 trim... Is slow as balls compared to my turbo car(one in the sig), but walks my DD(supercharged z24), and a Cobalt SS I recently did some work on... (ported blower, 2.8 pulley, 60s) As for our intake temps, they are very low also!

Get some better pics, I would like to see them.... Also, what turbo did you end up using? Specs(ar/trim?)






P&P Tuning
420.5whp / 359.8wtq

Re: Rear mount setup
Thursday, May 27, 2010 1:05 PM
I dont remember the specs just that it was small and perfect for my power goals and has minimal lag. Pretty soon it will be going to the dyno to see what the old eco is capable of. Good job on your builds, I have tried to keep the money invested in mine as resonable as possiable.



Remember... One test is worth a thousand expert opinions.
Re: Rear mount setup
Thursday, May 27, 2010 4:52 PM
I believe Pute had a rear mount setup.




I have no signiture
Re: Rear mount setup
Thursday, May 27, 2010 5:11 PM
Im afraid to ask if it is tuned.





Re: Rear mount setup
Thursday, May 27, 2010 5:31 PM
Why does that question always come up? My afr is correct and my pressure is at what my target was.


Remember... One test is worth a thousand expert opinions.

Re: Rear mount setup
Thursday, May 27, 2010 5:38 PM
Whalesac wrote:I believe Pute had a rear mount setup.
I believe that was converted into what QWK posted.
Josh A wrote:Why does that question always come up?
Because of people like me




fortune cookie say: better a delay than a disaster
Re: Rear mount setup
Thursday, May 27, 2010 5:39 PM
what did you do? and that transfered the wrong quote.... my bad


Remember... One test is worth a thousand expert opinions.
Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search