well...doing it with a steering wheel puller and ps puller. wish me luck!
Nate
Evolution of Cavyboy-->C22t--> C24na--->c24s/c
1995 Cavalier W/2k1 Engine
GM S/C 13.940@99.78pmh w/2.068 60ft
Good Luck, I hope its done by now lol
2002 Z28: Slp coldair Pac, Corsa Catback, 3200 stall
Yup. its done, it didn't take long. BUT.. it was a bitch to get the hub on. I think its still a C*nt hair or two from being flush with the shnout shaft. Think thats really bad? Runs fine. The boost hits 5psi right away now, and then onto 6 and see 7 at red line. Not bad. Nice improvement.
Now just have to figure out which injection kit works best for my application.
Nate
Evolution of Cavyboy-->C22t--> C24na--->c24s/c
1995 Cavalier W/2k1 Engine
GM S/C 13.940@99.78pmh w/2.068 60ft
C24s/c wrote:Yup. its done, it didn't take long. BUT.. it was a bitch to get the hub on. I think its still a C*nt hair or two from being flush with the shnout shaft. Think thats really bad? Runs fine. The boost hits 5psi right away now, and then onto 6 and see 7 at red line. Not bad. Nice improvement.
Now just have to figure out which injection kit works best for my application.
Nate
did you heat the hub up to put it on?
The First Twin Charged jbody
blue car (R.I.P) - 240whp @7psi..
silver car - 305whp 315lbs.tq @15psi (91 Octane) or 420whp & 425lbs.TQ @20psi (94 octane+Alcohol Injection)
All dynos run on a Mustang dyno
ps puller? I have the steering wheel puller, so please tell me what you used, when, etc.
....and I second Josh, did you heat the hub up?
.....here I go again, 2.7 or 2.6....I hate this debate!
I heated it up.. but not enough. Couldnt get it off after that. And didn't want to heat up the pulley and snout in case it wrecked the seal.
Power steering puller worked very well at taking it off.
Could have used a wheel puller, but i had this.
Ya, after it get the WI, and things are good. Pretty sure ill be upgrading to a 2.6 later on.
Nate
Evolution of Cavyboy-->C22t--> C24na--->c24s/c
1995 Cavalier W/2k1 Engine
GM S/C 13.940@99.78pmh w/2.068 60ft
^ Trust me u'll be upgrading very soon lol. I lasted a month on the 2.7 then it was time for the 2.6
You'll love it.
Glad to see you got the hub and stuff on. Did you get the 2.4 kit from pulleyboys like me and Josh?
Joe- Just buy both and then U wont have to tear yourself between the pulleys lol
Car is for Sale!Supercharger kit is for sale!
..lol me too, but i went all out.. 2.5"
Chris
'02 Z-24 Supercharged
13.7 @102.45 MPH Third Place, 2007 GMSC Bash SOLD AS OF 01MAR08
@!#$ it, 2.6" or bust.............so no mods required on the PB setup to work on the S/C, correct?
No the 2.6 has been remachined so it doesnt rub on the snout.
Car is for Sale!Supercharger kit is for sale!
i love you all!!!!!
seriously tho.......gettin my 2.6" sometime next week.....the day i get it is the day it will be on ill tell you that lol......yay!!!
ps.....im just a little tipsy now lol.....
2000 Camaro V6.
| SLP Loudmouth | CAI Intake | HID's |
