Head is done!!! Read more after the pics


















On a crappy note, I am going to have to grind a bit off the bottom of the rockers so that the roller will contact the valvestem, The spring retainers sit up a bit high but its an easy fix.

I installed some Jtuners pulleys today, Working out great so far! Also here is my cam I had reground from crane! 140 bucks baby!





And finaly the Cometic 2200 head gasket from Jtuners and the Jtuners pulley set!





Most of my audio is being sold, Im workingon a short block and direct port setup

Hope ya like my pics, I know they are performance parts but hey they can be pretty too

sweet man.



-Www.IznTrbl.Com-

I can Swear I have see that head in my garage before. lol lookin good as always.

KEN 2.2 wrote:I can Swear I have see that head in my garage before. lol lookin good as always.

wonder why

YAY!!!!!! OHV FOR LIFE!!!!!

bout time.....now get it done



P&P Tuning
420.5whp / 359.8wtq

Looks good.









~2014 New Z under the knife, same heart different body~
______________________
WHITECAVY no more
2012 numbers - 4SPD AUTOMATIC!!
328 HP
306 TQ

sweet... now it'll perform as well as it looks!

Hey Aaron, its gonna feel like a whole new car once its all installed and broken in. I just got my head, cam, and valvetrain done and installed about 6 months ago. Good luck and get 'er done.

Beautiful!



JBOK.org & Insane-Customs.com

I could go for some head right about now...

Nice work...NOW PUT IT IN!



www.kronosperformance.com / 732-742-8837

Sweet. Engine parts are beautiful to some.

I have to say, though...It's just a little bit scary how much it looks like styrofoam when you look this close:

lol, all the 2.2 heads that I've seen look like foam too. Hope it holds up to boost ok haha

looks good! Nice rockers!

noice work man

Yes i would also like some head lol

looks good, are u going from show to go now or something?

Quiklilcav wrote:Sweet. Engine parts are beautiful to some.

I have to say, though...It's just a little bit scary how much it looks like styrofoam when you look this close:

considering thats how there made yeah I imagne thats how it would look.



Im a level 32 joedm newb flamer.

Deputy D Styl3 wrote:looks good, are u going from show to go now or something?

Its possibal to have both...

Looks good overall. Should be a nice gain. Only problem I have is the guides look like they have been grinded down a bit. That's sweet for flow and such but not for longevity.....


http://www.cardomain.com/ride/448390

Mmmmmm! I want a head!



- Darren

ontariocavs.com -||- phewes.snowpants.org -||- zukiworld.com

hstylez wrote:Looks good overall. Should be a nice gain. Only problem I have is the guides look like they have been grinded down a bit. That's sweet for flow and such but not for longevity.....

Bout 90% sure they did not get touched, AMS knows is my daily driver

Nice! Have you had the car dyno'd before? I'd like to see how much of a gain you get.

16's beware here comes Phlatcav..


How much did the porting run ya?

L33tJbody (Brandon Gathye) wrote:16's beware here comes Phlatcav..


How much did the porting run ya?

sorry cheif, head dont go on till the block is finished and the direct port installed. so is 16's you best guess

oooh...direct port nitrous injection. big boi here gonna run 15s now

seriously though. its an automatic 2200, with 19"s and a body kit. even with a 100 shot direct port i would say low 15s at best. not knockin ya, i think your car looks tight. just saying that the performance probly wont throw down any earth shattering numbers